reducer价格优选企业,圣霖国际客户至上

允许输入法兰：

不能大于或小于临级减速机的标准尺寸，如减速机PLE80?的标准法兰为80mm,其临级的减速级是PLE60?和PLE120，PLE80?允许法兰不应小于60mm,也不能大于120mm。

Allow input flange

It can't be greater than or less than the standard of the reducer. For example, the standard flange of reducer PLE80 is 80mm, and the deceleration stage of its reducer is PLE60?减速机的作用1)降速同时提高输出扭矩，扭矩输出比例按步进电机输出乘减速比，但要注意不能超出减速机额定扭矩。 PLE120, PLE80? The maximum allowable flange should not be less than 60mm, nor greater than 120mm.

减速机性能特点

1,产品采用模块化设计,电动机输入,输入轴和孔类型三个方面,并配置脚,法兰安装,适用于各种有效的减变速传动,可以直接取代无级调速,摆线。

2、能源消耗低、噪音低、振动小,减速机达96%。

3,使用特殊的宽带宽压力电动机,当加载在20 hz - 60赫兹频率范围内正常使用。

4、齿轮渗碳淬火热处理工艺,采用独特的低噪声齿齿形设计,确保产品的使用寿命。

Performance characteristics of reducer

1, the product adopts modular design, motor input, input shaft and hole type three aspects, and equipped with feet, flange installation, suitable for all kinds of effective variable speed tran***ission, which can directly replace stepless speed regulation and cycloidal.

2, the energy cumption is low, the noise is low, the vibration is ***all, and the efficiency of the reducer is up to 96%.

3, the use of a special wide band wide pressure motor when loaded in the range of 20 Hz - 60 Hz is normally used.

4, gear carburizing and quenching heat treatment process, using a unique low noise tooth profile design to ensure the service life of the product.

齿轮声辐射特征分析 在选择用不同结构形式的齿轮时，对其特定结构建立声辐射模型，进行动力学分析，对齿轮传动系统噪声进行预先评估。但为获得硬齿面采用的渗碳淬硬使齿轮产生变形，导致齿轮传动噪声增大，寿命缩短。以便根据使用者的不同要求（使用场所，是 否无人操作，是否在城区内，地上、地下建筑物有无特定要求，是否有噪声防护，或无其他特定要求）去满足。

The acoustic radiation characteristic analysis of gear in the selection of gear with different structure forms, set up the acoustic radiation model to its specific structure, carry on the dynamic analysis, and evaluate the gear tran***ission system noise in advance. In order to meet the users' requirements (use sites, unmanned operati, whether there are specific requirements in the urban area, ground or underground buildings, noise protection, or other specific requirements).

减速机内部齿轮齿形修整（修缘和修根）和齿顶倒角 将齿顶的齿形切削成比正确的渐开曲线略呈凸形。当齿轮齿面受外力产生变形时，可以避免对与之啮合的齿轮产生干涉，并且可以降低噪音，延长齿轮寿命。

The internal gear of the reducer is trimmed (trim and trim) and tooth top chamfering to make the tooth shape of the tooth top convex than the correct involute curve. When the gear tooth surface is deformed by external force, it can ***oid interference to the gears engaged with it, and can reduce noise and prolong the service life of gears.